Mount the panel to the PT-10 case, using nuts to hold it on, then attach the PCB. I still managed to mess that up, mistakenly using all green wires for the LED and all orange for the power button. I should add that I can hear (and see) the laser module move slightly when the Play/Pause button is pressed to power on the player, providing it is going to switch on. See Compendium III § 313.6(C)(2) and 17 U.S.C. Place the panel on the PT-10 case, turn it over and see where it overlaps. You should have already tested the base PCB before now, so after inserting the master PIC and the 74HC595 and 74HC165 and connecting the LCD, you can turn it on and see if the switches and rotary encoders work. PCBs over. At this point, you'll need to raise the base PCB so it is level with the CS PCB and panel (the rotary encoder knobs will raise this off the work surface). The trouble with the Colorado River, it will be recalled, began in September, 1904. The California Development Company, promoters of the Imperial land colony, needed more water for agricultural purposes than their old irrigation ditch was then supplying, and to remedy the shortage an incision was made in the banks of the river at a point about four miles below the old tapping point, and below the international boundary line between the United States and Mexico.

The best way to strip the insulation from the wires is to lightly score with a knife on the flat side, i.e. cut half-way through the insulation, not cutting to the wire, then do small cuts between each wire (from the score line to the end), then pull off each little bit of insulation with pliers, being careful not to grip the wire too much and pull the wire out. Depending on the amount of JB-Weld used on the corner screws, you might need to trim the PT-10 mount holes, making them like countersunk screw holes (tapered out). Trim the mount until the hole is not overlapped. At this point, you'll need to trim a little bit off the top-left mount because it overlaps with the "SID R" LED. The further point, then, which merits attention is that the telegraphic communications between Great Britain and Canada are singularly ample and direct.

The cables should be connected so the cable sits flat against the top side of the CS PCB and the bottom side of the base PCB, so the solder joints are on the inside of the bent cable. This makes for a very strong connection with little stress on the solder joints or the exposed wire. DSL, or a satellite dish, or a wireless connection. I use 100mil spacing ribbon cable. Then use the holes of the PCB to bend the ends of the wire - insert cable so 2mm of wire (about the thickness of the PCB) is visible between the top of the PCB and the start of the insulation, what is control cable then bend 90 degrees. This means you should first cut lengths of 50mm and then strip 5mm of insulation of either end, and then bend the ends of the wires 90 degrees about 2mm from the insulation, towards the ribbed side. Place CS PCB face up, turned 90 degrees anticlockwise, so the pads to solder on the right side. Place base PCB face down, with the pads to solder on the left side.

Ideally you should not make a raised solder joint on this side, only get solder to be sucked into the hole, to hold the cables in place so you can do proper solder joints on the other side. Make sure there are NO SHORTS between any two adjacent pins of the ribbon cable joints. Do proper solder joints of all the pads. Make sure you do not put cable in the extra "GND" pads Put all eight 8-wire cables in, plus the single 2-wire cable. For each cable, insert it from the top into the pads on both sides, checking it is perpendicular to both PCBs and maintaining both PCBs are parallel. Five are owned by two British companies, and the remaining seven by two American companies. Coupled with ready-made JST cables, this is a much simpler approach and allows the two boards to be separated easily. The cable twist allows both floppy drives to be configured identically (for drive selection) when installed (for manufacturing convenience), yet operationally, can be uniquely selected as either the first drive or the second drive based on cable position. SATA drives are allowed to be connected to data without power, and to power without data.